Saturday, December 2, 2017

Energy Star Qualified, Haier HC17SF15RB 1.7 Cubic Feet Refrigerator/Freezer

Haier HC17SF15RB

Ships from and sold by Amazon.com. Gift-wrap available.

    Half-width Freezer Compartment with Ice Cube Tray
    Full-width Slide-out Wire Shelf
    Full-width and Half-width Door Storage Shelf; 2 Liter Bottle Storage
    Manual Defrost with Adjustable Thermostat
    Recessed Door Handle; Space Saving Flat back Design



Technical Details
Brand Name
Haier
Model Info
HC17SF15RB
Item Weight
30 pounds
Product Dimensions
17.9 x 19.4 x 18.9 inches
Item model number
HC17SF15RB
Capacity
1.7 cubic_feet
Installation Type
Free Standing
Part Number
HC17SF15RB
Form Factor
Stand Alone
Color
Black
Voltage
120 volts
Crispers/Drawers
1
Door Hinges
Reversible
Door Material Type
Stainless Steel
Certification
energy_star
Material Type
Stainless-Steel
Batteries Included?
No
Batteries Required?
No


iNsTALLiNG yOuR REfRiGERATOR
unpacking your Refrigerator
Remove all packaging material. This includes the foam base and all adhesive tape holding the refrigerator accessories inside and outside.
Inspect and remove any remains of packing, tape or printed materials before powering on the refrigerator.

   cAuTiON
Risk of Fire or Explosion due to puncture refrigerant tubing. Flammable refriger-ant used. Handle with care when moving refrigerator to avoid either damaging the refrigerant tubing or increasing the risk of a leak.
Leveling your Refrigerator
•  Your refrigerator has two leveling legs which are located in the front bottom corners of your refrigerator. After properly placing your refrigerator in its final position, you can level your refrigerator.
•  Leveling legs can be adjusted by turning them counterclockwise to raise your refrigerator or by turning them clockwise to lower your refrigerator. The refrigerator door will close easier when the leveling legs are extended.
proper Air circulation
•  To ensure your refrigerator works at the maximum efficiency it was designed for, you should install it in a location where there is proper air circulation, plumbing and electrical connections.
•  The following are recommended clearances around the refrigerator:
Sides...............4"
Top..................4"
Back.................4"
Door Alignment
1.  Remove the top hinge cover by using a flathead screwdriver. Place the head under the front edge of the cap and gently lift.
2.  Loosen the top hinge screws using a Phillips head screw driver.
3.  Adjust the door or put a spacer in between and tighten the screws.
4.  Replace the top hinge cover by aligning the rear of the cover with the rear of the hinge. Press firmly on the front of the cover until it snaps in place

Electrical Requirement
•  Make sure there is a suitable power outlet (115 volts, 15 amps outlet) with proper grounding to power the refrigerator.
•  Avoid the use of three prong adapters or cutting off the third grounding prong in order to accommodate a two prong outlet. This is a dangerous practice since it provides no effective grounding for the refrigerator and may result in shock hazard.
use of Extension cords
•  Avoid the use of an extension cord because of potential safety hazards under certain conditions. If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot outlet that will accept the plug. The marked rating of the extension cord must be equal to or greater than the electrical rating of the appliance.

installation Limitations
•  Do not install your refrigerator in any location not properly insulated or heated, e.g. garage, etc. Your refrigerator was not designed to operate in temperature settings below 55 ̊ Fahrenheit.
•  Select a suitable location for the refrigerator on a hard even surface away from direct sunlight or heat source, e.g. radiators, baseboard heaters, cooking appliances, etc. Any floor unevenness should be corrected with the leveling legs located on the front bottom corners of the refrigerator.
NOTE:
As the door gets pressed in during shipping, after reversing the door, the gasket may have to be reset. This is done to prevent the cool refrigerated air from escaping. If there is a gap between the door gasket and the cabinet, set the gasket by gently pulling it out to seal the gap.